Shower Water Mineral Treatment With Silver Carbon & Maifen Stone Filter & Shower Head (Copy)

What You Get

Showersoft Water Softener

Construction : 316 Marine grade stainless steel

Threads : 1/2″ Female (screws to water inlet) 3/4” Male (screws to Showerfilter)

WaterMark Certified : Yes

Showersoft Filter

Construction : 316 Marine grade stainless steel

Threads : 3/4” Female (screws to Showersoft) 1/2″ Male (screws to shower hose)

Shower Head

High pressure 5 setting shower head

Rain Mode, Massage Mode, Mixed Mode, Pulse Mode, Spray Mode

Ball Swivel

Construction : Chromed brass

45 Degree Elbow

Threads : 1/2” Male/Female

High Pressure 5 Setting Shower Head

Threads : 1/2” Male/Female

Overall Length : 450mm (approximate)

Backing Plate

Construction : Stainless steel

Shower Filter Media

• Fine 304SS sieve
• Filter wadding
• 30ml Maifen rock
• 50ml Silver activated coconut carbon media

Comes partially assembled ready to install and use

How To Install The New Shower Softener, Filter & Shower Head

1. Make sure the water is off
2. Unscrew the old shower head from the wall
3. Screw the shower arm to the wall water inlet male thread and tighten
4. Screw the shower head to the end of the shower filter arm and tighten

Adjust the shower head so it is all aligned and point the shower head down

Turn the water on and make sure there are no leaks, if there is tighten the fitting

NOTE: Do not stand under the shower when you turn the water on. Turning the water on will flush the carbon media dust out of the filter.  Let the shower run for a few minutes and it is then safe to use.

Install is done…enjoy your shower!

How To Remove The Activated Carbon & Maifen Stone Filter Media

Tip: Use a plastic or metal bowl and a wooden or plastic chopping board

Removing The Old Shower Media

1. Make sure the water is turned off
2. Unscrew the shower head assembly from the shower filter
3. Unscrew the shower filter from the shower softener
4. To loosen up the media remove the wadding and then tap the female thread end of the filter on the chopping board. DO NOT tap this on stone/laminate or other constructed bench top
5. Put the filter over a bowl and insert the wooden dowel in the mail thread end of the filter housing and push the media out the filter (you may need to give it a tap with a hammer or something similar)
6. Give the filter housing a wash to clean it out

Installing The New Shower Media

We suggest doing this in a plastic or metal bowl

1. Stand the filter housing up in the bowl
2. Insert the mesh disc and make sure it is sitting across the outlet of the filter housing
3. Insert a piece of filter wadding and using the wooden dowel push this against the mesh disc
4. Pour the Maifen stone into the filter housing and give it a few taps to set in place
5. Insert a second piece of filter wadding using the wooden dowel
6. Pour half of the carbon media into the filter housing and give it a few taps to set in place
7. Repeat the above until you have all of the carbon media in the housing
8. Insert the rubber washer with mesh in the female housing
9. Screw the filter housing to the shower softener and reconnect the shower head assembly
10. Turn the water on and make sure there are no leaks, if there is tighten the fittings

NOTE: Do not stand under the shower when you turn the water on. Turning the water on will flush the carbon media dust out of the filter.  Let the shower run for a few minutes and it is then safe to use.

CONGRATULATIONS the new shower media filter replacement is done so celebrate by having a shower!

Replacement Filter Kit Contains

• Wooden dowel
• 304SS mesh disc
• Filter wadding
• 30ml Maifen rock
• 50ml Silver activated carbon media
• 3/4” Washer with mesh insert

How Long Will It Last?

The Shower Softener & Filter Housing

Manufactured from 316 marine grade stainless steel these fitting will last 10 to 15 years or even longer before needing to be replaced

Filter Media

Depending on the number of people showering on a daily basis, the filter media will need to be replaced every 4 to 6 months or maybe sooner if your water is extremely dirty.

Changing the filter will take about 10 to 15 minutesDoes It Need Any Replacement Parts?

The shower softener has no replacement parts.  The filter media will need to be replaced.

How The Shower Water Conditioner & Softener Work?

The Softerwater conditioner alloy core produces a turbulent mineral attracting galvanic reaction reducing the electrical charge of minerals like calcium and magnesium found in all water supplies.  Non sticking mineral colloids are formed and flow through your water system in suspension giving a softer water that significantly reducers hard water scale problems.